# Correct way to hook up jumper cables

**Click here:** \
&#x20;\
&#x20;※ [**Correct way to hook up jumper cables**](http://chantkontheadta.datingvr.ru/?dt\&keyword=correct+way+to+hook+up+jumper+cables\&source=gitbook.com5_dating_poster) \
&#x20;\
&#x20;※ [**♥ Correct way to hook up jumper cables**](http://chantkontheadta.datingsvr.ru/?dt\&keyword=correct+way+to+hook+up+jumper+cables\&source=gitbook.com5_dating_poster) \
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\\

It could be the computer. If there is corrosion on the terminal, twist the jaws of the clamp until it cuts through the corrosion and into the metal. Safety First You should consider all safety risks before performing any basic maintenance or repair on your car.\
&#x20;![correct way to hook up jumper cables](http://moziru.com/images/drawn-power-line-electric-post-13.jpg)\\

Connect the red cable to the positive terminal on the battery, and the black cable to the negative terminal. Forrest Hartman Find the solo video and audio inputs on your TV. Erhalten Sie personalisierte Werbung von Partnern unseres Vertrauens Dies bedeutet nicht mehr, sondern personalisierte Werbung. Plug the charger into an outlet. If your car still does not start, see the. It's important to make sure the metal ends of the note cables do not touch each other or any metal surfaces on the car until they are connected to the correct battery terminals. The positive post may have a red cable attached, but it's best to look for a plus or minus sign to determine its polarity. Jumpstarters like thecan also for smartphones and other devices via their USB ports. Then, connect one of the black clamps to the negative terminal on the donor battery and attach the other black clamp to the engine block on the vehicle with the dead battery.

Manchmal zeigen wir Ihnen personalisierte Werbung, indem wir anhand Ihrer Aktivitäten auf unseren Seiten und Produkten fundierte Vermutungen über Ihre Interessen anstellen. Safety First You should consider all safety risks before performing any basic maintenance or repair on your car.\
&#x20;![correct way to hook up jumper cables](http://img-aws.ehowcdn.com/600x400/cpi.studiod.com/www_ehow_com/i.ehow.com/images/a05/mk/o7/correct-way-jump-start-car-800x800.jpg)\\

**How to Use Jumper Cables** - When you really need them, any set is better than none at all, but if you're buying new jumper cables, ones that are 4 to 6 gauge and at least 20 feet 6 meters long. Start the vehicle with the dead battery and let the two vehicles idle for a few minutes.\
&#x20;![correct way to hook up jumper cables](http://www.diychatroom.com/attachments/f18/57412d1347723723-adding-light-switch-outlet-light-correct-wiring-new-bitmap-image-2.jpg)\\

Parking the cars so they face each other is the best option. If you aren't sure where the batteries are under each hood, take a peek before you park. Important Tip: Never drive with your hood raised. Not only does it hamper visibility, but you could damage your hood components or the hood itself. Continue Reading Below On the dead battery, attach the positive red cable to the battery, but attach the negative black cable to a section of bare metal in the engine compartment. Even a nut or bolt end will do. Not only will this protect your car's electrical system from any surges, it's always safer under the hood with the engine off. They should be clearly marked on the battery itself. On newer cars, the positive + side often has a red cover over the battery post and wires. This can be as small as the head of a bolt located nearby. Important Tips: Attach the jumper cable to the most secure attachment point you can find on the car's permanent battery cables. If they are corroded, it may help to wiggle the jumper cable end around a bit while it's attached to the car's cables or battery. In the old days, , which could turn into flammable gas around the battery. This gas could explode if the cable caused a spark just above the battery. Some people tend to clamp the negative cable onto the rubber cable covering of the positive side while they walk across to the other car. If one of those sharp teeth were to pierce the rubber cover and reach the wires inside, you could do serious electrical damage to one or both vehicles. If the battery in the dead was was really badly drained, it may help to leave them connected for a minute with the good car running before you try to start the dead car. Turn the key in the dead car to start and it should fire right up. If you continue to have starting problems, you might need to. You can disconnect the jumper cables right away. Disconnecting the Jumper Cables Disconnecting the jumper cables doesn't need to happen in any specific order, but be sure you don't let the red and black cables touch each other at the end when they are still connected to one battery. If the dead car doesn't turn over or turns over very slowly, check to see if your battery or connections are corroded. If they are, sometimes a little wiggling while the cable clamp is connected will make your connection better. Otherwise, it might be a good time to. If your car still does not start, see the.
